1. Plug CA-42 cable to USB without

1. Plug CA-42 cable to USB without any connection. And install drivers about this cable. Under device manager you will see new device. Pls note that Com Port number. Mine is Com Port 11
2. Unplug USB side and plug small sockets on HDD serial port. I found GND already. If your system cannot talk with HDD switch Tx with Rx

3. Apply power to HDD, motor will start to spin up and plug USB to your computer

4. Setup Hyperterminal. My port is on Com 11 :
Bits per second : 38400 Data bits : 8 Parity : N Stop bits : 1 Row control : N

5. After this point when you press Ctrl + Z keys you have to see below screen on hyperterminal if you cannot see switch Rx and Tx

ASCII Diag mode
F3 T>

now here are the commands : (P.S. be careful to uppercase and lowercase while you write commands)

F3 T>/2
F3 2>Z

If it’s ok you have to see.

Spin Down Complete
Elapsed Time 0.140 msecs

If you see after Z command

LED:000000CC FAddr:0025DDD9 or similar message listen to your HDD. When motor is down (not spin) press Ctrl + Z next /2 and next Z . Now you have to see Spin Down Complete on screen.

Now do not move HDD and remove the paper between PCB and Data pins. (Meanwhile all the cables are must be attached on HDD “USB and power cables”). Be sure to tight screws especially on data pin side.

If you’re ready press U key and spin up motor

F3 2>U

After a while you have to see below message

Spin Up Complete Elapsed Time 8.363 secs

After pressing U if you will see below message there was a problem on communication between PCB and HDD. Means PCB is not touching pins correctly. You have to start over everything from 1st step.

DiagError 00006008
Spin Error
Elapsed Time 39.083 secs
R/W Status 2 R/W Error 84150180

After Spin Up process motor will keep up spinning

New command is : /1

F3 2>/1

Next : N1

F3 1>N1

and : /T

F3 1>/T

Now while USB is attached to the HDD remove power cable from HDD. Wait 10-15 second and plug the power cable back. HDD will start to spin up
If you cannot type any command on screen pls press Ctrl + Z. And type this command i4,1,22 (be careful to uppercase/lowercase)

F3 T>i4,1,22

Now is the heart of commands : m0,2,2,,,,,22 (yes there are 5 commas)

F3 T>m0,2,2,,,,,22

After this command progress will take some time. Don’t worry. Get a cup of coffee and relax. You have to see similar to below message. Important one is “User Partition Format Successful “ now we can reach our HDD again.

Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 14, Max Certify Rewrite Retries = 00C8
User Partition Format 3% complete, Zone 00, Pass 00, LBA 00004AA5, ErrCode 000 00080, Elapsed Time 0 mins 30 secs
User Partition Format Successful – Elapsed Time 0 mins 30 secs
Zone re-format was skipped.

Remove everythings from HDD and connect to the computer in normal way. Turn on computer you are able to see your HDD again.

Of course copy all important data’s on another media in any case.

If you have any further questions please contact to me

Hasil (Bahasa Indonesia) 1:

1. Plug CA-42 cable to USB without any connection. And install drivers about this cable. Under device manager you will see new device. Pls note that Com Port number. Mine is Com Port 112. Unplug USB side and plug small sockets on HDD serial port. I found GND already. If your system cannot talk with HDD switch Tx with Rx3. Apply power to HDD, motor will start to spin up and plug USB to your computer4. Setup Hyperterminal. My port is on Com 11 :Bits per second : 38400 Data bits : 8 Parity : N Stop bits : 1 Row control : N5. After this point when you press Ctrl + Z keys you have to see below screen on hyperterminal if you cannot see switch Rx and TxASCII Diag modeF3 T>now here are the commands : (P.S. be careful to uppercase and lowercase while you write commands)F3 T>/2F3 2>ZIf it’s ok you have to see.Spin Down CompleteElapsed Time 0.140 msecsIf you see after Z commandLED:000000CC FAddr:0025DDD9 or similar message listen to your HDD. When motor is down (not spin) press Ctrl + Z next /2 and next Z . Now you have to see Spin Down Complete on screen.Now do not move HDD and remove the paper between PCB and Data pins. (Meanwhile all the cables are must be attached on HDD “USB and power cables”). Be sure to tight screws especially on data pin side.If you’re ready press U key and spin up motorF3 2>UAfter a while you have to see below messageSpin Up Complete Elapsed Time 8.363 secsAfter pressing U if you will see below message there was a problem on communication between PCB and HDD. Means PCB is not touching pins correctly. You have to start over everything from 1st step.DiagError 00006008Spin ErrorElapsed Time 39.083 secsR/W Status 2 R/W Error 84150180After Spin Up process motor will keep up spinningNew command is : /1F3 2>/1Next : N1F3 1>N1and : /TF3 1>/TNow while USB is attached to the HDD remove power cable from HDD. Wait 10-15 second and plug the power cable back. HDD will start to spin upIf you cannot type any command on screen pls press Ctrl + Z. And type this command i4,1,22 (be careful to uppercase/lowercase)F3 T>i4,1,22Now is the heart of commands : m0,2,2,,,,,22 (yes there are 5 commas)F3 T>m0,2,2,,,,,22After this command progress will take some time. Don’t worry. Get a cup of coffee and relax. You have to see similar to below message. Important one is “User Partition Format Successful “ now we can reach our HDD again.Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 14, Max Certify Rewrite Retries = 00C8User Partition Format 3% complete, Zone 00, Pass 00, LBA 00004AA5, ErrCode 000 00080, Elapsed Time 0 mins 30 secsUser Partition Format Successful – Elapsed Time 0 mins 30 secsZone re-format was skipped.Remove everythings from HDD and connect to the computer in normal way. Turn on computer you are able to see your HDD again.Tentu saja menyalin semua data penting di pada media lain dalam hal apapun.Jika Anda memiliki lebih pertanyaan silahkan hubungi saya