Hasil (
Bahasa Indonesia) 1:
[Salinan]Disalin!
Bagaimana membuat layang-layang Layang-layang terdiri dari bagian-bagian dasar ini: • Tulang belakang. Tongkat down, atau vertikal yang Anda membangun Anda layang-layang di sekitar. • Spar. Stick(s) dukungan, yang ditempatkan crossways atau miring ke tulang belakang. Kadang-kadang mereka melengkung atau sujud. • Frame. Bergabung dengan tulang belakang dan Spar, biasanya dengan tali menghubungkan mereka berakhir, yang membentuk bentuk layang-layang dan membuat dukungan untuk sampul. • Penutup. Kertas, plastik, atau kain, yang mencakup kerangka untuk membuat layang-layang. • Kekang. Satu atau beberapa string yang melekat pada tulang belakang atau Spar, yang membantu mengendalikan layang-layang di udara. • Garis terbang. String berlari dari kekang layang-layang, mana Anda memegang untuk terbang layang-layang. • Ekor. Strip panjang kertas atau plastik pita yang membantu untuk menyeimbangkan layang-layang dalam penerbangan. Layang-layang tidak semua perlu ekor. • Dansa. Objek yang Anda gunakan untuk angin baris Anda terbang, untuk tetap bentuk mendapatkan kusut atau terbang pergi. LAYANG-LAYANG BERLIANBahan:• daging tali atau benang Taman tipis • scotch tape atau lem • 1 lembar kertas kuat (102 cm x 102 cm) • 2 kuat, lurus kayu batang bambu atau kayu doweling 90cm dan 102cm • spidol, cat atau krayon untuk menghias Anda kite.1. membuat salib dengan dua tongkat, dengan tongkat pendek diletakkan horizontal tongkat panjang. Pastikan bahwa kedua sisi potongan salib sama lebar.2. Tie the two sticks together with the string in such a way as to make sure that they are at right angles to each other. A good way to ensure that the joint is strong to put a dab of glue to stick it in place.3. Cut a notch at each end of both sticks. Make it deep enough for the type of string you are using to fit in to. Cut a piece of string long enough to stretch all around the kite frame. Make a loop in the top notch and fasten it by wrapping the string around the stick. Stretch the string through the notch at one end of the cross-piece, and make another loop at the bottom. Stretch the string through the notch at one end of the loop at the bottom. Stretch the string through the notch at the other end of the cross-piece. Finish by wrapping the string a few times around the top of the stick and cutting off what you don't need. This string frame must be taut, but not so tight as to warp the sticks.4. Lay the sail material flat and place the stick frame face down on top. Cut around it, leaving about 2-3cm for a margin. Fold these edges over the string frame and tape or glue it down so that the material is tight.5. Cut a piece of string about 122 cm long. and tie one end to the loop at the other end of the string to the loop at the bottom. Tie another small loop in the string just above the intersection of the two cross pieces. This will be the kite's bridle, the string to which the flying line is attached.6. Make a tail by tying a small ribbon roughly every 10cm along the length of string. Attach the tail to the loop at the bottom of the kite.7. Decorate!Tips:• A properly located pivot point is generally located slightly ahead of the centre of gravity. • Cut away from you! • Spray can glue is really good for patching up paper kites. • Stability is improved by the use of an effective bow and a flexible tail. • Hold your kite up by the string when you are finished to see if it is balanced. You can balance it by putting more paper on one side. • Kites are different each time you make one, so slight adjustments might need to be made for each kite.
Sedang diterjemahkan, harap tunggu..
