Galaxy Y S5360.Download Android 2.3

Galaxy Y S5360.
Download Android 2.3.6 DDMD1 Gingerbread Firmware for Samsung Galaxy Y S5360.
Procedure:

Step 1: Download both the files in a specific folder and extract them. You’ll find these three files inside the firmware package:

CSC_S5360_ODDMD1.tar.md5
MODEM_S5360_DDMD1.tar.md5
PDA_S5360_DDMD1.tar.md5


Step 2: Now switch off your Galaxy Y completely until it vibrates.

Step 3: Enter into downloading mode now. For the same, keep pressing and holding ‘Home Button (middle button) + Volume down key + Power Button’ simultaneously until you see a warning message on the screen (Refer Screenshot). Just press Volume Up button to continue. This will land you into downloading mode.



Step 4: Keep the phone as it is in downloading mode and connect it to your PC using USB cable. Ensure that you’ve installed device specific drivers on PC to detect the phone when connected (As mentioned in pre-requisites).

Step 5: Launch the ‘Odin Multi Downloader_v3.07′software which you have just downloaded & extracted on your PC. As soon as you launch it, the ID:COM section in it will turn blue with a random COM port number below it. You’ll also see an ‘Added’ message which will appear in the message box window. If it’s not showing, then check whether you have properly installed those device drivers on your PC or not.



Step 6: Now tick the Auto Reboot option and F.Reset option present on the Odin window (Refer screenshot). Do not tick or un-tick any other options. Keep them as they are.



Step 7: Select the ‘PDA’ tab on the Odin window and navigate to the ‘PDA_S5360_DDMD1.tar.md5‘ from the firmware package & select it.



Step 8: Similarly select the ‘PHONE’ tab located below the PDA tab and navigate to the ‘MODEM_S5360_DDMD1.tar.md5‘ file & select it.



Step 9: Finally select the ‘CSC’ tab and navigate to the ‘CSC_S5360_ODDMD1.tar.md5‘ from the firmware package and select it.



Step 10: After doing everything as mentioned above, just navigate to the ‘Start’ option on the Odin window and select it. This will initiate the actual firmware flashing process. Your Galaxy Y will automatically reboot itself while the process goes on. Do not remove the USB cable until the process completes fully. Be patient for few minutes.



Step 11: As soon as the process completes, you’ll see the ID:COM section on the Odin window is turned green with the message ‘Pass’ below it. This will confirm that you have successfully flashed your Galaxy Y with the latest Android 2.3.6 Gingerbread DDMD1 Indian firmware. You may now safely disconnect your phone by removing the USB cable.

Note: If the process fails or if Odin gets stuck or in case your device gets boot loops, then close the Odin window, remove battery from your Galaxy Y and re-insert it. Again go into downloading mode and follow the whole procedure as given above.

Step 12: After successfully completing the process, switch off the phone and boot into recovery mode. For that, press and hold Home Button (middle button) + Volume up key + Power Button simultaneously until the recovery mode appears.

Note: Touch will not work here in this recovery mode. So all you need to do is use Volume Up and Volume Down keys for navigation and Home button (Middle button) for selection.

Step 13: On the recovery mode, navigate to the ‘Wipe data/factory reset’ option and the ‘Wipe Cache partition’ option for clearing all the data and caches present in your phones memory. This is essential in solving the boot loops issue.

Step 14: After wiping data/cache you’ll again land into recovery mode. Just select ‘reboot system now’ option to restart the phone.

Success

Congrats! You have successfully flashed the latest Android 2.3.6 DDMD1 Official Gingerbread firmware on your Samsung Galaxy Y GT-S5360. You may confirm the same from Menu->Settings->About Phone. Remember that this is a stock ROM so you can flash this whenever you want to restore the warranty or restore the default system on your mobile. Don’t forget to tell us your views and experience after using this firmware. I have made this article very simple so that you’ll understand it easily, still if you have any doubt/query or any problem regarding the given stuff then do contact me through the comments section given below. I’ll provide an exact solution for your every problem. Till then Enjoy!

Hasil (Bahasa Indonesia) 1:

Galaxy Y S5360.DDMD1 download Android 2.3.6 Gingerbread Firmware untuk Samsung Galaxy Y S5360.Prosedur:Langkah 1: Download kedua file dalam folder tertentu dan ekstrak mereka. Anda akan menemukan tiga file ini di dalam paket firmware:CSC_S5360_ODDMD1.tar.MD5MODEM_S5360_DDMD1.tar.MD5PDA_S5360_DDMD1.tar.MD5Langkah 2: Sekarang menonaktifkan Y Galaxy Anda benar-benar sampai itu bergetar.Langkah 3: Masuk ke dalam men-download modus sekarang. Yang sama, tetap menekan dan menahan 'Home Button (tombol tengah) + Volume tombol + tombol Power' secara bersamaan sampai Anda melihat pesan peringatan pada layar (lihat Screenshot). Hanya tekan tombol Volume naik terus. Ini akan mendarat Anda ke dalam men-download modus.Langkah 4: Menyimpan telepon seperti di men-download modus dan menghubungkannya ke PC menggunakan kabel USB. Pastikan bahwa Anda telah menginstal driver perangkat tertentu pada PC untuk mendeteksi telepon ketika terhubung (seperti yang disebutkan dalam pra-syarat).Langkah 5: Jalankan ' Odin Multi Downloader_v3.07′software yang Anda telah download & diekstrak pada PC Anda. Segera setelah Anda memulai itu, Bagian ID:COM di dalamnya akan mengubah biru dengan nomor port COM acak di bawah ini. Anda juga akan melihat pesan 'Tambah' yang akan muncul di jendela kotak pesan. Jika itu tidak menunjukkan, kemudian cek apakah Anda memiliki benar menginstal driver perangkat tersebut pada PC Anda atau tidak.Langkah 6: Sekarang mencentang pilihan Auto Reboot dan F.Reset pilihan hadir pada jendela Odin (Lihat screenshot). Melakukan tidak mencentang atau un-mencentang pilihan lain. Menjaga mereka karena mereka.Step 7: Select the ‘PDA’ tab on the Odin window and navigate to the ‘PDA_S5360_DDMD1.tar.md5‘ from the firmware package & select it.Step 8: Similarly select the ‘PHONE’ tab located below the PDA tab and navigate to the ‘MODEM_S5360_DDMD1.tar.md5‘ file & select it.Step 9: Finally select the ‘CSC’ tab and navigate to the ‘CSC_S5360_ODDMD1.tar.md5‘ from the firmware package and select it.Step 10: After doing everything as mentioned above, just navigate to the ‘Start’ option on the Odin window and select it. This will initiate the actual firmware flashing process. Your Galaxy Y will automatically reboot itself while the process goes on. Do not remove the USB cable until the process completes fully. Be patient for few minutes.Step 11: As soon as the process completes, you’ll see the ID:COM section on the Odin window is turned green with the message ‘Pass’ below it. This will confirm that you have successfully flashed your Galaxy Y with the latest Android 2.3.6 Gingerbread DDMD1 Indian firmware. You may now safely disconnect your phone by removing the USB cable.Note: If the process fails or if Odin gets stuck or in case your device gets boot loops, then close the Odin window, remove battery from your Galaxy Y and re-insert it. Again go into downloading mode and follow the whole procedure as given above.Langkah 12: Setelah berhasil menyelesaikan proses, matikan telepon dan boot ke dalam recovery mode. Untuk itu, tekan dan tahan tombol Home (tombol tengah) + Volume up kunci + tombol Power secara bersamaan sampai recovery mode muncul.Catatan: Touch tidak akan bekerja di sini dalam modus pemulihan ini. Jadi semua yang Anda perlu lakukan adalah menggunakan tombol Volume naik dan Volume Down untuk navigasi dan tombol Home (tengah tombol) untuk seleksi.Langkah 13: Pada recovery mode, navigasikan ke opsi 'Wipe data/pabrik reset' dan 'Partisi usap Cache' pilihan untuk menghapus semua data dan cache hadir di memori telepon Anda. Hal ini penting dalam memecahkan masalah loop boot.Langkah 14: Setelah menyeka data cache Anda akan kembali tanah ke dalam recovery mode. Hanya pilih opsi 'reboot sistem sekarang' untuk me-restart telepon.SuksesCongrats! Anda telah berhasil berkelebat 2.3.6 Android terbaru firmware Gingerbread resmi DDMD1 pada Samsung Galaxy Y GT-S5360. Anda dapat mengkonfirmasi sama dari Menu -> Settings -> tentang telepon. Ingatlah bahwa ini adalah saham ROM sehingga Anda dapat flash ini setiap kali Anda ingin mengembalikan garansi atau mengembalikan sistem default pada ponsel Anda. Jangan lupa untuk memberitahu kami pandangan dan pengalaman setelah menggunakan firmware ini. Saya telah membuat artikel ini sangat sederhana sehingga Anda akan memahaminya dengan mudah, namun jika Anda memiliki keraguan/pertanyaan atau masalah tentang hal-hal tertentu yang kemudian hubungi saya melalui bagian komentar yang diberikan di bawah ini. Aku akan memberikan solusi yang tepat untuk setiap masalah Anda. Sampai kemudian nikmati!